From  

Tutorials: BandStructureAndDOS

Learning Objectives

Introduction

The aim of this tutorial is to enable you to compute band structures using CASTEP and introduce you to a few of the tools which allow you to visualise the band structure and density of electronic states computed using CASTEP. The band structure of metals and semiconductors will be plotted so that you can look at the differences between different types of systems.

First you will look at the CASTEP input files (.cell and .param) used to produce band structure information.

Next you will use the perl script dispersion.pl which can be used to take CASTEP output and plot band structure diagrams.

Then you will use orbitals2bands. A tool which provides more information about the orbitals that contribute to different bands in your band structure diagram.

Finally you will look at the band structure of iron, to show how magnetic systems can be studied using CASTEP, you will also plot the density of states of iron using dos.pl.

You will need:

In addition to CASTEP and the suite of tools it comes with you will need:

These are free programs commonly available with many Linux distributions, if they are not installed on your system, you can install them following instructions on their websites or by speaking nicely to your sysadmin.

Example files:

Copy the example files
wget http://www.castep.org/files/bandstructure.tgz
Then untar and unzip it using:
gunzip bandstructure.tgz
tar -xvf bandstructure.tar

Example 1 - Graphite.

Move into the graphite directory, look at the CASTEP .cell and .param files and notice the differences from the previous single point energy runs.

To the .param file the task (which lets CASTEP know what you want it to do) needs to be changed to:
task : bandstructure
The .cell file requires a path through the Brillouin Zone along which you want the bandstructure to be plotted:
%BLOCK BS_KPOINT_PATH
0.0000 0.00000 0.00000 ! G
0.0000 0.00000 0.50000 ! A
-0.3333 0.66667 0.50000 ! H
-0.3333 0.66667 0.00000 ! K
0.0000 0.00000 0.00000 ! G
0.0000 0.50000 0.00000 ! M
0.0000 0.50000 0.50000 ! L
-0.3333 0.66667 0.50000 ! H
%ENDBLOCK BS_KPOINT_PATH

Run CASTEP with graphite as the seed e.g. $ castep graphite or $ mpirun -n 16 castep.mpi graphite

Once the CASTEP calculation has finished a graphite.bands file will be present in the directory. A band structure plot can be viewed by using the dispersion.pl tool. $ dispersion.pl -xg -bs -symmetry hexagonal graphite.bands
The -xg option tells dispersion.pl that you are using grace to plot the band structure, the -bs option tells the script that you want to plot using CASTEP output files, the -symmetry hexagonal option labels the high symmetry points on the bands structure plot. (you will need to have grace installed in order for this to work)

When you view this band structure plot you will notice the bands are coloured from lowest to highest energy. Using information about the wavefunction CASTEP can improve this band structure plot, so bands are coloured due to the orbitals that contribute. The orbitals2bands tool can be used to alter the Si.bands file represent the orbitals that contribute to the bands. This tool can be run in the same directory that you ran CASTEP in.
The program orbitals2bands overwrites your Si.bands file, so it's best to copy it to another file to preserve it
$ cp graphite.bands graphite.bands.orig
$ orbitals2bands graphite

Example 2 - Silicon and Aluminium.

Very similar to example 1, but this time comparing a semiconductor and a metal, both with FCC crystal structures.

Go into the silicon and aluminium directories and compute the band structures as above.

The dispersion symmetry option needs to be told that these are FCC materials, not hexagonal.

Compare the band structure of the Silicon and Aluminium crystals.

Example 3 - Iron

In the iron directory there is a set of input files for iron. As iron is a magnetic system you need to instruct CASTEP that it is spin polarised. You also need to set up the calculation with the total spin set to a non-zero value, in order to find the magnetic ground state. (If you're interested you could try removing the spin : 1 line from the Fe.param file and see what happens). You set the spin in the .param file:

spin : 1
spin_polarised : true

The path through the Brillouin Zone is found in the Fe.cell file.

Run the iron computation using CASTEP and plot the band structure for iron using dispersion.pl. You might find the -mono option to dispersion.pl to be useful - it colours the bands by spin channel.

Iron's Density of States

To plot the density of states of iron, we need to run CASTEP again, instead of computing the band structure along a high symmetry line, we compute it on a grid. To your Fe.cell file, remove the bs_kpoint_path block and replace it with:

BS_KPOINT_MP_GRID 12 12 12

Run CASTEP using these new input files then use the dos.pl plotting script
dos.pl -xg -bs -w 0.2 Fe.bands

Can you relate the features in the DOS to those in the Bandstructure?

You might find the -mirror option useful. The -w option sets the Gaussian broadening in eV. Try smaller (0.05) and larger (0.5) values - explain what you see.

DOS for the other crystals in this tutorial can be computed in a similar way.

Retrieved from http://www.castep.org/Tutorials/BandStructureAndDOS
Page last modified on September 16, 2013, at 11:06 PM